A-A-1500 - Sealer Surface (Latex Block Filler)
This description covers a ready-mixed latex block filler for interior and exterior use on concrete and masonry surfaces.
A-A-1556 - Sealing Compound (Elastomeric Joint Sealants) (S/S By Astm-C920)
A-A-2210 - Filler, Wood, Paste
A-A-272 - Caulking Compounds
This Commercial Item Description covers three types of 1-part caulking compounds suitable for use as recommended by the manufacturers for sealing, caulking, filling, leveling and glazing in general exterior architectural service and structures.
A-A-2884 - Neat'S-Foot Oil
This Commercial Item Description covers non-sulfonated neat's-foot oil.
A-A-2982 - Coating Compound, Butuminous, Fillers, Solvent Type, Aluminum Pigmented
A-A-373 - Glazing Compound, Sash (Metal) For Back Bedding And Face Glazing (Not For Channel Or Stop Glazing) (S/S By Astm-C669)
A-A-378 - Putty, Linseed Oil Type, (For Wood Sash Glazing)
A-A-52408 - Preservative Coating, Rubber : For Rubber Surfaces
This CID covers preservative coating for the protection of natural or synthetic rubber items such as tires, track pads, bogey wheels, gaskets, hoses, and others. Its purpose is to eliminate deterioration due to oxidation, ultraviolet light and ozone. The material can be used where solvent vapor is not a hazard.
A-A-52495 - Sealing Compound, Non-Curing, Polybutene
This CID covers two types of mastic sealing compounds. The sealing compounds are polybutene based and non-curing.
A-A-56025 - Paste, Conductive
This commercial item description covers three types of conductive coatings or paste used as a thick film screen printable conductor.
AWPA-A1 - Creosote & Oil-Type Preservatives,Standard Methods For Analysis
This method of test covers the determination of the coke residue (fixed carbon) of creosote, coal tar, and creosote-coal tar solutions.
AWPA-A11 - Treated Wood & Treating Solutions By Atomic Absorption Spectroscopy
This method provides for atomic absorption spectrometric analysis of treated wood and treating solutions.
AWPA-A2 - Preservatives, Waterborne, & Fire Retardant Formulations, Standard Methods For Analysis Of
Methods for analysis of materials used in standard water-borne preservatives and fire-retardant formulations are given for the determination of the following.
AWPA-A3 - Penetration Of Preservatives & Fire Retardants, Standard Methods For Determining
These are the methods for determining the depth of preservative penetration in treated wood in order to decide whether the treated product meets acceptance levels as prescribed in treatment standards.
AWPA-A4 - Wood Preservatives, Standard Methods For
AWPA-A5 - Preservatives, Oil-Borne, Analysis Of, Standard Methods For
This method covers the determination of the total acidity of a dry chemical sample expressed as the pentachlorophenol content of the sample.
AWPA-A6 - Wood, Oil-Type Preservatives & Water In, Method For The Determination Of
This assay method is suitable for the determination of creosote, coal tar, petroleum, and their solutions in treated wood when the sample contains at least 5.0 grams of wood and one gram of oil.
AWPA-A7 - Wood, Preparing, For Chemical Analysis, Standard Wet Ashing Procedure For
A procedure for decomposition of wood as an initial step for analysis for the constituents arsenic, chromium, copper, phosphate, and zinc, all of which may then be analyzed according to the procedures given in AWPA standards A2, A9, and A11.
AWPA-A8 - Creosote Or Creosote-Coal Tar Solution From Freshly Treated Piles, Poles, Or Timber (Squeeze Method) Qualitative Recover Of
This method covers the removal of creosote or creosote-coal tar solution from freshly treated wood and the removal of water from the recovered oil to render it suitable for qualitative testing.
AWPA-A9 - Wood, Treated, & Treating Solutions By X-Ray Spectroscopy, Standard Method For Analysis Of
AWPA-F1 - Creosote-Coal Tar Solution (Up To 50 Percent Tar) And Coal Tar (Coke Oven Tar) Volume And Specific Gravity Correction Tables For Creosote
AWPA-F4 - Creosote-Petroleum Solutions, Standard Volume Correction Table For
AWPA-F5 - Salt Solutions, Preservative, Volume Correction Factors For
AWPA-F6 - Factors And Correction Tables, Miscellaneous Conversion
AWPA-M4 - Wood Products, Preservative-Treated, Standard For The Care Of
AWPA-P1 - Land & Resh Water For Coal Tar Creosote, Standard For
AWPA-P11 - Creosote-Pentachcorophenol Wood Preservative Solution, Standard For
AWPA-P12 - Creosote-Coal Tar Solution To Be Used In The Treatment Of Marine (Costal Waters) Piles And Timbers, Standard For
AWPA-P13 - Creosote Coal Tar To Be Used In The Treatment Of Marine (Coastal Waters) Piles & Timbers Standard For
AWPA-P2 - Creosote & Creosote Solutions, Standard For
AWPA-P3 - Oil Solution, Creosote-Petroleum, Standard For
AWPA-P4 - Creosote, Petroleum Oil For Blending With, Standard For
AWPA-P5 - Preservative, Waterborne, Standards For
These standards cover waterborne preservative formulations expressed on the oxide basis and prescribe maximum and/or minimum values of acceptability in either solid, paste, or solution formulations for use in the preservative treatment of wood.
AWPA-P7 - Field Cuts, Creosote For Brush Or Spray Treatment, Standard For
AWPA-P8 - Oil-Borne Preservatives
AWPA-P9 - Solvents & Formulation For Organic Preservative Systems, Standard For
C-N-200 - Neats Foot Oil (S/S By A-A-2884)
Neat's-foot oil covered by this specification is suitable for the treatment of leather.
DOD-C-2687 - ( Images) Compound, Battery Sealing (Metric)
This specification covers compounds for sealing lead-acid storage batteries.
DOD-R-18708 - Rust-Arresting Coating, Shipboard Exterior, Gray, Navy Formula No. 123G Metric
This specification covers a rust-arresting compound which will temporarily arrest ferrous metal corrosion and remove some rust until proper surface preparation and painting can be accomplished. This product may be used where air pollution regulations apply.
DOD-S-82708 - ( Images) Sealing Compound, Preformed (Metric)
This specification covers two types of preformed sealing compound for filling voids in a guided missile rocket motor.
DOD-STD-1371 - Inspection Procedure For Use Of Anaerobic Thread Locking Compounds With Studs (S/S By Sae-J2270)
This standard provides an inspection procedure to assure that studs installed with an anaerobic thread locking compound have achieved the necessary backout resistance.
FED-STD-293 - Tape, Pressure Sensitive Adhesive (Fsc 8030)
HH-C-536 - Compound, Plumbing-Fixture-Setting
The plumbing-fixture setting compound shall be of one grade.
HH-T-30 - Tape, Pipe Coating, Coal Tar, Hot Applied, And Primer
JAN-A-669 - Anti-Seize-Compound, White-Lead-Base, General-Purpose (For Threaded Fittings) (Use Tt-A-580)
JAN-C-168 - Compound, Calking (For Wooden Vessels) (S/S By Mil-C-18969)
JAN-C-238 - Coating, Exterior, Camouflage And Rust-Inhibiting (For Processed And Nonprocessed Food Cans) (S/S By Mil-C-10506)
JAN-C-693 - Cement, Metallurgical, Air-Setting, High Temperature
JAN-P-115 - Packaging And Packing For Overseas Shipment - Compound, Sealing, Dipcoating
JAN-P-604 - Protective Coating System, Phonolic Resin Base, Heat&Hardening &For The Interiors Of Potable&Water Tanks&
L-T-1512 - ( Images) Tape, Pressure Sensitive Adhesive, Pipe Wrapping
This specification establishes the requirements for a pressure sensitive adhesive tape, suitable for corrosion prevention of exterior surfaces of metal pipe.
L-T-80 - Tape, Pressure-Sensitive Adhesive (Aluminum-Backed)
This specification establishes the requirements for an aluminum foil backed pressure-sensitive adhesive tape designed for use in sealing applications where the properties of good weather resistance, reflectivity, and moisture vapor transmission resistance are required.
MIL-A-12352 - Antiseize Compound, Threads, For Steam And Water Lines (Use Tt-S-1732)
MIL-A-13881 - Anti-Seize Compound, Mica-Base (For Threaded Fittings)
This specification covers one type of mica-base anti-seize compound, for use in the threads of automotive engine spark plugs, and in other applications involving high temperatures.
MIL-A-38267 - Application Of Polyurethane Fuel Tank Coatings
MIL-B-12121 - Plastic, Coating Compound, Strippable (Sprayable)
MIL-C-0083933 - Corrosion Preventive Compound, Cold-Application (For Motor Vehicles)
MIL-C-102 - Coating Compound, Bituminous, Solvent Cut Back, Box And Crate Topcoating
MIL-C-10382 - Corrosion Preventive, Petrolatum, Spraying Application: For Food Handling Machinery And Equipment
This specification covers one grade of petroleum base corrosion preventive suitable for use by spraying application on food handling machinery and equipment.
MIL-C-10506 - Coating, Exterior For Tinned Food Cans (Use Tt-C-495)
MIL-C-1068 - Compound, Water-Repellent, Textile Finish
MIL-C-11080 - Coating, Corrosion-Resistant
This specification covers one type of an aluminum corrosion-resistant coating.
MIL-C-11728 - Compound, Corrosion-Inhibiting And Lubricating, For Gas Cylinder Cap Threads
MIL-C-11794 - Compound, Caulking
MIL-C-11796 - Corrosion Preventive Compound, Petrolatum, Hot Application
This specification covers a suitably formulated petrolatum-base corrosion preventive compound.
MIL-C-12178 - Corrosion-Preventive Compound, Trifluorovinyl Chloride, For Use With Oxygen Equipment
MIL-C-1219 - Cement, Iron And Steel (S/S By Qq-C-100)
MIL-C-12599 - Coating, Clear, Acrylic (Pressurized Dispenser) (Use Tt-L-50)
MIL-C-13125 - Compound: Mounting For Optical Lens Blanks
MIL-C-13370 - Coating Material, Heat-Resistant, For Ferrous Surfaces
MIL-C-13388 - Compound, Asphaltic, Fire Retardant
MIL-C-13704 - Cement, Sealing Or Plugging
MIL-C-13783 - Compound, Waterproofing (For Small Arms Ammunition)
MIL-C-13950 - Coating Compound, Bituminous, Solvent (For Railway Rolling Stock)
MIL-C-14201 - Corrosion Preventive, Soft-Film, Cold Application (S/S By Mil-C-16173)
MIL-C-15074 - Corrosion Preventive, Fingerprint Remover
This specification covers one type of corrosion preventive intended for use as a fingerprint remover and as a temporary preservative for metallic items.
MIL-C-15166 - Pigment, Copper-Cuprous Oxide (Use Mil-P-15169)
MIL-C-15167 - Corrosion Preventive Compound, Petrolatum, Pigmented, Hot Application (S/S By Mil-C-11796)
MIL-C-15170 - Coating Compound, Abrasive Filled Synthetic Binder, Lightweight, Nonslip
MIL-C-15203 - Coating Compound, Bituminous, Emulsion Type, Coal Tar Base
MIL-C-15275 - Coating, Plastic (For Canvas And Cotton Drill)
MIL-C-15705 - Calking Compound (Liquid Polymer Polysulfide Synthetic Rubber; Formula No. 112, For Metal Enclosures)
MIL-C-15799 - Cement, Sealing (Use Mil-A-388)
MIL-C-16231 - Calking Compound (For Metal Seams) (S/S By Mil-C-18969)
MIL-C-16555 - Coating Compound, Strippable, Sprayable
This specification covers a strippable coating compound for application by spraying on painted or unpainted metal surfaces to seal openings and provide protection against corrosion. This specification meets Air Pollution Regulations (Rule 66).
MIL-C-16558 - Coating, Organic (For Covering Struts And Other Exposed Surfaces)
MIL-C-18255 - Calking Compound, Synthetic Rubber Base, Wooden Deck Seam Application (See Notice 1 For Replacement Information)
This specification covers synthetic rubber base calking compounds, complete with such primers as may be necessary for use on new, wood decking or in regrooved seams of wood decking from which oil, sawdust, oakum, marine glue, or other foreign substances have been removed.
MIL-C-1828 - Compound, Spray, For Upper Leather
MIL-C-1829 - Compound, Oil, Sole Treating
MIL-C-18480 - Coating Compound, Bituminous, Solvent, Coal-Tar Base
This specification covers a cold-applied coal-tar base coating compound for use on steel structures under conditions where it is not feasible to use a hot-applied coal-tar enamel.
MIL-C-18969 - Calking Compounds Metal Seam And Wood Seam (Use Mil-C-18255)
MIL-C-19459 - Corrosion Inhibiting Compound (For Torpedo Mark 37 Mod 0 And Related Application) (S/S By Mil-Prf-16173)
MIL-C-19471 - Corrosion Preventive Compound, Cold Application, Non-Tacky (S/S By Mil-C-16173)
MIL-C-19993 - Coating Compound, Fibrous Glass Thermal Insulation Board, Water Vapor Barrier(S/S By Mil-19565 Now Mil-Prf-19565)
MIL-C-20551 - Compound, Luting
MIL-C-21066 - Coating System, Plastisol (S/S By Mil-P-20689)
MIL-C-21067 - Coating Compound, Synthetic Rubber, For Exposed Steel Surfaces
This specification covers synthetic rubber coating compound intended for use in protecting exposed steel surfaces from corrosion.
MIL-C-22235 - Corrosion Preventive Oil, Nonstaining
MIL-C-22395 - Compound Sealing, Thermal Insulation Pipe Covering-Fire-, Water-, And Weather-Resistant
This specification covers flexible, fire resistant and water-proof end sealing compounds for thermal insulation exterior steam systems operating at temperatures up to 400 deg. F.
MIL-C-22804 - Cement, Sealing, Double Planking
MIL-C-23050 - Compound, Rust Retarding, Spray On Type, Ballast Tank Preservative
MIL-C-23112 - Corrosion Preventice, Fire Resistant (S/S By Mil-H-19457)
MIL-C-23403 - Compound, Soft Film, Corrosion-Preventative, Non-Staining
MIL-C-23411 - Corrosion Preventive Compounds, Clear (S/S By Mil-C-81309)
MIL-C-23760 - Coating, Sprayable, Strippable, Protective, For Packaging Of Weapons Systems And Components, Application Of
This specification covers the detailed requirements and procedures to be followed in the applicaiton of sprayable, strippable coatings approved under MIL-C-6799 for the protection of painted and unpainted, metallic or plastic surfaces for weapon systems and components. The details contained herein shall not be construed as modifying any requirements of the basic material specifications.
MIL-C-24205 - Calking Compound, Modified Epoxy Base, Wooden Deck Seam Application
MIL-C-26703 - Coating, Interior, For Metal Containers (Supersedes 20029)
MIL-C-27315 - Coating, Systems, Elastomeric Thermally Reflective And Rain Erosion Resistant (S/S By Mil-C-83445)
MIL-C-27725 - Coating, Corrosion Preventive, For Aircraft Integral Fuel Tanks (S/S By Sae-Ams-C-27725)
MIL-C-3004 - Coating, Fire-Resistant, Adhesive (For Repairing Surface Of Fibrous Glass Insulation Board) (Use Mil-A-3316)
MIL-C-3254 - Coating-System, Bridging, Strippable Sprayable
MIL-C-3299 - Canister, Colored Smoke, 155-Mm. Shell, M3
MIL-C-38713 - Coating Compound, Elastic, Polysulfide (S/S By Mil-Prf-81733)
MIL-C-3923 - Calking Compound
MIL-C-40084 - Corrosion Preventive Compound, Water-Emulsifiable, Oil Type
This specification covers a fire-resistant, water-emulsified, oil type corrosion preventative compound to be used as a rust inhibiting coating.
MIL-C-43374 - Coating Compound (Touch Up, For Air Supported Radome)
MIL-C-4484 - Coating Plastic (For Refinishing Leather) (Supersedes 14154)
MIL-C-46095 - Compound, Sealing, Low Temperature, Rotation
MIL-C-46157 - Coating Compound, Temporary Protective For Retrograde Materials
This specification covers a temporary protective coating for use over aluminum or painted metal substrates. It is suitable for use under AIR POLLUTION REGULATIONS.
MIL-C-47016 - Compound, Modified Silicone Rubber, Heat Resistant
MIL-C-47069 - Coating, Electrically Conductive, Air-Drying
This specification cover one type of coating, electrically conductive, air-drying.
MIL-C-47070 - Compound, Urethane
MIL-C-47071 - Coating, Ablative, Phenolic-Epoxy Resin System
This specification covers the requirements for a two component ablative coating.
MIL-C-47072 - Curing Agent, Epoxy Resin
MIL-C-47121 - Compound, Sealing, Polysulfide Rubber
This specification covers a polysulfide rubber compound for sealing electrical and mechanical components as a protection against corrosion, moisture, and mechanical damage.
MIL-C-47127 - Cloth, Polyester Fabric, Chlorosulfonated Polyethylene Coated, Flame Resistant (S/S By Mil-C-43285)
This specification covers one type of flame resistant, chlorosulfonated polyethylene coated polyester fiber cloth.
MIL-C-47161 - Coating, Corrosion Resistant
MIL-C-47163 - Compound, Rubber, Silicone, High Dielectric Properties, Room Temperature Vulcanizing
MIL-C-47164 - Compound, Plastic Polyurethane
MIL-C-47167 - Compound, Sealant Anti-Sieze
This specification covers the requirements for one type of non-hardening sealing and anti-sieze compound capable of distortion without fracture when applied to thread couplings.
MIL-C-47168 - Coating, Ablative, Spray Type High Temperature Resistant
MIL-C-47214 - Coating, Protective, For Insulation Sheet Cork
MIL-C-47244 - Coating, Ablative Resistant
This specification covers the requirements for a two-component, room temperature curing, filled, thermosetting, modified epoxy resin system that resists abrasion and erosion at extreme temperatures.
MIL-C-47246 - Coatings, Ablative, Application Of
This specification establishes the requirements for the application of ablative coating primer and ablative coating.
MIL-C-47247 - Coating, Protective, Resin, Silicone
This specification covers one type of a rigid one-component silicone resin for use as a protective coating for the surfaces and junctions of transistors, diodes, and other electronic devices.
MIL-C-5537 - Cellulose Acetate Butyrate
This specification covers one type and grade of cellulose acetate butyrate. In powder or pellet form, it is used in organic protective coatings.
MIL-C-81384 - Coating, Sprayable, Clear, Weatherproof, For Protection Of Fibrous Containers
MIL-C-82594 - Corrosion Preventive Compound And Surface Sealer For Nonferrous Metals
This specification covers a solvent-dispersed compound which penetrates metal pores and forms a microthin, clear, protective coating, and seal to prevent corrosion when applied by aerosol, brush, dip, or spray to nonferrous metals.
MIL-C-82644 - Compounds, Epoxy, Encapsulating
MIL-C-83019 - Coating, Polyurethane, For Protection Of Integral Fuel Tank Sealing Compound
This specification covers a coating material to be applied over aircraft integral fuel tank sealing compound for protection against fuel and fuel contaminants.
MIL-C-83466 - Coating, Polyurethane, Aliphatic Isocyanate, Thermal Flux Resistant For Aerospace Applications (S/S By Mil-C-83286)
MIL-C-83933 - Corrosion Preventive Compounds Cold Application (For Motor Vehicles)
This specification covers four grades of solvent dispersed corrosion preventive compounds for motor vehicles.
MIL-C-83982 - Compound, Sealing, Fluid Resistant (S/S By Mil-S-81733)
MIL-C-8514 - Coating Compound, Metal Retreatment, Resin-Acid (Asg)
This specification covers one type and grade of pretreatment coating for use on clean metal surface of all types as a treatment prior to application of the coating system. The smooth finish spray-type coating may also be applied by brushing, roller coating, or swabbing.
MIL-C-87179 - Coating, Protective, Solvent Removable, For Microcircuits (S/S By Sae-Ams2535)
This specification covers solvent-soluble conformal coatings which are suitable for application to monolithic and hybrid microcircuits.
MIL-C-972 - Compound, Rust-Preventive, Thin-Film (Polar Type) (S/S By Mil-C-16173)
MIL-D-16651 - Deck Covering, Lightweight, Nonslip, Nonsparking, And Sealing Compound, Fabric Deck-Covering (Use Mil-D-17951)
MIL-D-17419 - Drawing, Engineering And Associated Documentation Preparation And Microfilming Of (For Electronic Equipment)
MIL-D-9063 - Desealant, Integral Fuel And Oil Tanks (S/S By Mil-R-81294)
This specification covers desealing materials for aircraft integral fuel and oil tanks that do not have faying surface rubber.
MIL-DTL-3301 - Compound, Asphaltic, Hot-Melt (Cavity Lining)
This specification covers a hot-melt asphaltic compound for coating the inner walls of metal cases prior to filling with explosives.
MIL-DTL-3688 - Wax Emulsion (Rust Inhibiting)
This specification covers a type of wax emulsion suitable for use as a rust inhibiting coating for general weatherproofing when applied to articles (see 6.1).
MIL-DTL-450 - Coating Compound, Bituminous Solvent Type, Black (For Ammunition)
This specification covers an asphalt compound for coating the surfaces of ammunition cavities prior to filling with explosives. It provides for an additional composition of material suitable for use in areas with specific air pollution regulations (see 6.1 and 6.4).
MIL-DTL-82604 - Compound, Asphaltic, High Melting Hotmelt (Cavity Lining)
This specification covers a high-melting hotmelt asphaltic compound for coating the inner walls of metal cases prior to filling with explosives.
MIL-DTL-82633 - Compound, Polymeric Elastomer, Thermosetting
This specification covers a two-part, cured-in-place, polymeric thermosetting compound having elastomeric and thermal properties for sealing or padding the tail portion of the explosive cavities of bombs. Curing takes place at room temperature with a minimum of exotherm.
MIL-DTL-85054 - Corrosion Preventive Compound, Water-Displacing, Transparent (Formerly Amlguard)
This specification covers a transparent, water-displacing, corrosion preventive compound, available in high and low volatile organic compound (VOC) types, which may be applied by brushing or spraying (see 6.1).
MIL-E-47166 - Epoxy Cement, Conductive, Room Temperature Curing
MIL-F-3622 - Flame-Resistant Compound, Fabric (Colorless, Emulsifiable)
MIL-F-46032 - Fungus-Resistant Treatment For Sandbags, Copper Processes
This specification covers the processing of sandbags with copper compounds for protection against fungus attack. These processes are not intended for application to materials which will come into frequent contact with a person's skin.
MIL-F-9118 - Finish, For Glass Fabric
MIL-G-12376 - Gasket Forming Compound, For Petroleum Products Pipe (Use Mil-S-7916)
MIL-G-26138 - Glove Set, Protective Fire-Fighting
MIL-G-46884 - Glass, Metal Sealing (S/S By Astm-F105)
MIL-HDBK-696 - Plastic Coating Compound, Strippable, Hot And Cold Dip
MIL-L-10095 - Leather Dressing, Preservative And Mildew Preventive
MIL-L-52696 - Laminating Resin
This specification covers the requirements for an opoxy laminating resin and hardener for impregnating fiber glass cloth to form a rigid adhesive repair over a damaged and prepared fiber glass base.
MIL-M-13295 - Mildew Resistant Compound, Textile (For Field Retreatment) (Use Tt-P-595)
MIL-M-15205 - Metal Conditioning Compound (Use Mil-C-22235)
MIL-M-17222 - Mildew Resistant Compound, 2, 2, Methylenebis (4-Chlorophenol)
MIL-M-17231 - Mildew Resistant Compound, Copper Naphthenate
MIL-M-5658 - Mildew Proofing Of Fabrics, Threads And Cordages, Copper Processes For
MIL-M-81999 - Molding Compound, Reversion Resistant, Non-Carcinogen Curing Polyurethane, Aircraft Structure
This specification covers the requirements for two component, chemically elevated temperature curing, reversion resistant polyether polyurethane compounds for filling and sealing aircraft structures for added strength and protection against the passage of air, liquids and vapors.
MIL-N-1056 - Neat S-Foot, Oil, Sulphomated
MIL-P-00906 - Preservative, Wood, Oil Borne; For Ship And Boat Use (S/S By Mil-W-18142)
MIL-P-11520 - Preservative Coating, Rubber: For Rubber Surfaces (S/S By A-A-52408)
MIL-P-149 - Plastic Coating Compound, Strippable (Hot Dipping)
This specification covers a strippable plastic coating for use in the preservation and packaging of metallic parts (see 6.1).
MIL-P-15076 - Flame Spray Coating, Polymer Powder
MIL-P-15142 - Putty, Spotting, White
MIL-P-15143 - Protective-Coating (Heat-Hardening), Phenol-Formaldehyde
MIL-P-15159 - Preservative Coating, Canvas (Navy) (S/S By Tt-P-595)
MIL-P-18623 - Plastic Coating Compound, Electrical Cable Splice Sealing, Naval Shipboard
MIL-P-19980 - Preservative Coating, Cotton Matting, Fire-Resistant
MIL-P-20088 - Preservation Solution Concentrate, Sonar Sea Chest
This specification covers preservation solution concentrate for use as a filling solution in sonar sea chests. This material may be used in geographical areas where air pollution regulations exist (see 6.3).
MIL-P-20628 - Putty, Sealing (For Bolted Steel Storage Tanks)
MIL-P-20689 - Plastic Plastisol (For Coating Metallic Objects) (S/S By A-A-59464)
This specification covers plastisols with primer, suitable for coating metallic objects to provide protection from corrosion and abrasion, and to impart a comfortable feel.
MIL-P-22841 - Paper, Masking, Pressure-Sensitive, Adhesive-Edged
MIL-P-23242 - Plastic Coating Compound, Strippable - Electroplating
This specification covers the requirements for one type of hot-dip, stop-off, strippable plastic coating intended for masking metallic areas not to be plated during an electroplating process.
MIL-P-3826 - Pitch, Burgundy
MIL-P-3840 - Paint, Camouflage, Bituminous&Emulsion Adhesive
MIL-P-45021 - Plastic Coating Compound, Strippable, Cold Dipping, 120 Deg F. (49 Deg. C) (S/S By Mil-C-6799 Now Mil-Prf-6799, Mil-C-16173 Now Mil-Prf-16173, Mil-C-16555, Mil-C-23760)
MIL-P-47215 - Primer, Ablative Resistant Coating
This specification covers the requirements for a room-temperature-drying primer used as a metal treatment in conjunction with ablative resistant coating.
MIL-P-83455 - Potting Compound, Two Component, Rtv, Fluorosilicone
MIL-P-906 - Preservative, Wood, Water-Repellent (S/S By Tt-W-572)
MIL-PRF-16173 - Corrosion Preventive Compound, Solvent Cutback, Cold-Application
This specification covers solvent-dispersed corrosion preventive compounds that deposit thin, easily removable films after evaporation of solvent.
MIL-PRF-18487 - Compound, Gun Slushing
The gun slushing compound covered by this specification is intended for usc as a corrosion preventive on ferrous and nonferrous metals which arc stored indoors or outdoors for indefinite periods. (See 6.1.)
MIL-PRF-19565 - Coating Compounds, Thermal Insulation, Fire, And Water-Resistant, Vapor-Barrier
This specification covers an interior vapor-barrier coating for insulated refrigerant and chilled water lines.
MIL-PRF-23586 - Sealing Compound (With Accelerator), Silicone Rubber, Electrical
This specification covers the requirements for electrical silicone rubber sealing compounds that are not resistant to fuel. These compounds are intended for use in the temperature range of -62 to +204 Deg. C (-80 to +400 Deg. F).
MIL-PRF-24176 - Cement, Epoxy, Metal Repair And Hull Smoothing (Metric)
This specification covers a two -component epoxy cement for use in filling rough or pitted metal surfaces.
MIL-PRF-3043 - Resin Coating, Permanent, For Engine Components And Metal Parts
This specification covers one type of permanent resin coating for surfaces of engine components and metal parts.
MIL-PRF-62218 - Corrosion Preventive Compounds, Cold Application (For New And Fielded Motor Vehicles And Trailers) (S/S By A-A-59295)
This specification covers solvent dispersed corrosion preventive compounds, referred to herein as "compound," for spray, brush, or dip application on new and fielded motor vehicles and trailers (see 6.1).
MIL-PRF-81309 - Corrosion Preventive Compounds, Water Displacing, Ultra-Thin Film
This specification covers the requirements for three types and two classes containing two grades of propellants of ultra-thin film, water displacing, corrosion preventive compounds which may be applied by dipping, spraying, brushing or by spraying from self-pressurized containers (see 6.1).
MIL-PRF-81733 - Sealing And Coating Compound, Corrosion Inhibitive
This specification covers accelerated, room temperature curing synthetic rubber compounds used in the sealing and coating of metal components on weapons and aircraft systems for protection against corrosion. The Class 1 sealing compound is effective over a continuous operating temperature range of ??65?? to +250?? F (??54?? to +121?? C). The Class 2 sealing compound is effective over a continuous operating temperature range of ??80?? to +320?? F (??62?? to +160?? C).
MIL-PRF-81904 - Coating Compound, Thermal-Insulation
This specification covers asbestos-free, thermal-insulating coating compound. The thermal protection coating is used for the exterior surfaces of aircraft ordnance to delay cook-off during exposure to a liquid fuel fire (see 6.1).
MIL-PRF-83483 - Antiseize Thread Compound, Molybdenum Disulfide-Petrolatum
This specification presents requirements for one type of anti-seize thread compound composed of molybdenum disulfide and petrolatum.
MIL-PRF-8516 - Sealing Compound, Synethetic Rubber, Electric Connectors And Electric Systems, Chemically Cured
This specification covers a two-component, chemically cured synthetic rubber compound for insulating, sealing, reinforcing, and corrosion protection of electric connectors, wiring, and other electric apparatus. This specification has provisions for shelf-life extension (see 3.2.4).
MIL-PRF-907 - Antiseize Thread Compound, High Temperature
This specification covers antiseize compound for use on threads of steel nuts, studs, bolts and other mating surfaces, including those of superheated steam installations, at temperatures up to 1050 degrees Fahrenheit (degrees F) (566 degrees Celsius (degrees C)).
MIL-R-10036 - Rust Arresting Coating (For Treatment Of Rusted Metal)
This specification covers a clear (unpigmented) coating based on vegetable and animal oils for use on rusted metal and painted surfaces to arrest further corrosion. It provides two compositions, one of which is suitable for use under Air Pollution Regulations (see 6.5).
MIL-R-20091 - Rubber (Synthetic) And Cement For Lining Ferrous Pipe And Fittings (For Saltwater, Lines)
MIL-R-21006 - Rust Retarding Compound, Flotation Type, Ballast Tank Protective
MIL-R-46082 - Retaining Compounds, Single Component, Anaerobic (S/S By Astm-D5363)
This specification covers single-component, retaining compounds for assembling slip-fitted parts with varied clearances (see 6.4 & 6.15). The retaining compounds are for use as alternatives for press and shrink fits (see 6.1).
MIL-R-47013 - Rubber, Butyl, Special Grade
MIL-R-47120 - Rubber, Butyl (Resin Cured), Short Term Resistant To Hydrazine Type Fuels And Irfna
MIL-S-11030 - Sealing Compound, Single-Component, Non-Curing, Polysulfide Base
This specification covers single-component black, inert, thermoplastic, mastic, non-curing sealing compounds.
MIL-S-11031 - Sealing Compound, Adhesive. Curing (Polysulfide Base) (S/S By A-A-59293)
MIL-S-11388 - Sealing Material For Metal Container Seams
This specification covers a material used for sealing seams in the manufacture of hermetically sealed metal containers for packaging dry materials.
MIL-S-11515 - Sealing Tape, Wood-To-Metal And Metal-To-Metal Surfaces, Asphalt Base, Cotton Backed, Waterproof
MIL-S-12158 - Sealing Compound, Non-Curing, Polybutene (S/S By A-A-52495)
This specification covers two types of mastic sealing compounds. The sealing compounds are polybutene based and non-curing.
MIL-S-12243 - Sealing Compound, For Waterproofing Welding Electrodes.
MIL-S-14231 - Sealing Compound, Joint, Two Component, For Bolted Aluminum Or Steel Petroleum-Storage Tanks
MIL-S-15204 - Sealing Compound, Joint And Thread, High Temperature
This specification covers sealing compounds for use in threaded and fixed mechanical joints in equipment powered by steam or gas at temperatures up to 950 degrees Fahrenheit (deg. F) and pressure of 1200 pounds per square inch.
MIL-S-17175 - Sealing Compound, Asphalt Base, For Ammunition
MIL-S-17377 - Sealing Compound, Boiler-Casing
This specification covers boiler-casing sealing compound for use in sealing the joints in boiler casings against air leakage.
MIL-S-19653 - Sealing Compound (Wood Bedding)
This specification covers a permanently plastic, waterproofing sealing compound for use between inner and outer planking of double planked hulls, and on other faying surfaces of wooden craft to prevent the passage or accumulation of water and to resist deterioration by decay fungi.
MIL-S-22473 - Sealing, Locking, And Retaining Compounds: (Single Component) (S/S By Astm-D5363)
This specification covers single component compounds and their primers suitable for coating, locking and retaining metal parts.
MIL-S-23498 - Sealing Compound, Bearing Preservation, Synthetic Rubber Base
MIL-S-24340 - Sealing Compound, Deck, Polyurethane (Polyether Base)
This specification covers a chemically-curing flexible material, containing a polyether polyurethane compound for embedment and seams of wood decks and underlayment, and seams of metal-clad deck panels.
MIL-S-24522 - Sealer, Deck Covering (S/S By Tt-S-223)
MIL-S-2869 - Sealing Compound, Synthetic Rubber, Hose Cover Repair
MIL-S-3105 - Sealing Compound, Inert (For Use In Ammunition) (S/S By Mil-Dtl-82633)
This specification covers inert sealing compound for use as a nonreactive material for sealing, padding, or a combination of both in the nose and tail portions of the explosive cavity of bombs.
MIL-S-3802 - Sealer For Automotive Application
MIL-S-38228 - Sealing Compound, Environmental, For Aircraft Surfaces (S/S By Sae-Ams3265)
This specification covers temperature-resistant and weather-resistant synthetic rubber compounds for filling and sealing exterior surfaces of aircraft and missiles.
MIL-S-38249 - Sealing Compound, Firewall (S/S By Sae-Ams3374)
This specification covers flame-resistant, synthetic rubber compounds for sealing firewall structures.
MIL-S-38714 - Sealing Cartridge For Two Component Materials
This specification covers cartridges which are used to store, mix and apply sealants, adhesives, and similar materials.
MIL-S-3927 - Sealing Compound, Thread, Polymerizing Room Temperature (S/S By Mil-S-46163 And Mil-S-22473
MIL-S-40083 - Sealing And Retaining Compounds, Thread,Single Component
MIL-S-4383 - Sealing Compound, Topcoat, Fuel Tank, Buna-N Type (S/S By Sae-Ams-S-4383)
MIL-S-45180 - Sealing Compound, Gasket, Hydrocarbon Fluid And Water Resistant
This specification covers requirements for thread and gasket sealing compounds that are resistant to fuel, engine oils, and water.
MIL-S-46163 - Sealing, Lubricating And Wicking Compounds: Thread-Locking, Anaerobic, Single-Component (S/S By Astm-D5363)
This specification covers single-component anaerobic compounds suitable for thread-locking and sealing.
MIL-S-46897 - Sealing Compound, Polyurethane Foam
MIL-S-47015 - Sealer, Flexible Ablative
MIL-S-47122 - Sealing Compound
MIL-S-47123 - Sealant, Ablative, Silicone Base, Room Temperature Curing, And Primer
MIL-S-47162 - Sealant, Silicone Rubber Room Temperature Vulcanizing
MIL-S-47165 - Sealing Compound, High Tear Strength
MIL-S-47169 - Sealant, Filled Epoxy, For Gyroscopic Devices
MIL-S-47245 - Sealant, Electrically Conductive
MIL-S-47294 - Sealant, Silicone Rubber, Rtv, Non-Acetic Acid Evolving
MIL-S-48112 - Sealing Compound Butyl Rubber Sealant (For Use In Ammunition)
MIL-S-5043 - Sealing Compound; Synthetic Rubber, Catalyzed (For Integral Fuel Tanks) (S/S By Mil-S-7502 And Mil-S-8784)
MIL-S-5817 - Sealant, Fuel Tank, Polysulfide Polymer, Solvent-Type
MIL-S-7126 - Sealing Compounds, Synthetic Glass (Use Mil-S-11030 And Mil-S-7124)
MIL-S-7916 - SEALING COMPOUND, THREAD AND GASKET, FUEL, OIL, AND WATER RESISTANT (S/S BY SAE-AS-S-7916)
MIL-S-81323 - Sealing Compound, Non-Curing, (-65 Deg F To 350 Deg F) Groove Injection (For Integral Fuel Tanks)
MIL-S-81732 - Sealing Compound, Electrical, High Strength, Accelerator Required
This specification covers the requirements for a high temperature, high strength, reversion resistant, two part silicone sealing compound for various electrical applications within aircraft.
MIL-S-83315 - Sealing Compound, Aluminum Structure, Pressure And Weather Sealing, Low Density
MIL-S-83318 - Sealing Compound, Low Temperature Curing, Quick Repair Integral Fuel Tanks And Fuel Cell Cavities (S/S By Sae-Ams-S-83318)
This specification covers a two component, temperature??resistant ??65??F to +250??F (??54??C to +120??C), low temperature (20??F minimum) curing synthetic rubber compounds for quick repair of aircraft integral fuel tanks and fuel cell cavities. During application, the sealing compounds shall be a suitable, fluid consistency.
MIL-S-83384 - Silicone, Encapsulant, Room Temperature Curing, For Space Applications
MIL-S-83430 - Sealing Compound, Integral Fuel Tanks And Fuel Cell Cavities, Intermittent Use To 360 Deg. F (182 Deg. C) (S/S By Ams3276)
MIL-S-83432 - Sealing Compounds, Adhesive Bonded Structure
MIL-S-85312 - Sealing Compound, Noncuring, Polysulfide, Groove Injection, For Integral Fuel Tanks
MIL-S-85318 - Sealing Compound, Non-Carcinogen Curing Polyurethane (Polyether-Based), Electric Connectors And Electric Systems
This specification covers the requirements for a two-component, elevated temperature curing, reversion resistant polyether polyurethane compound for sealing and embedding electrical and electronic components in Military Weapons Systems.
MIL-S-85334 - Sealing Compound, Noncuring, Low Consistency, Silicone, Groove Injection, For Integral Fuel Tanks
This specification establishes the requirements for one type of inert, permanently mastic silicone type sealing compound modified with a flow control additive, for sealing or resealing integral fuel tanks on military aircraft.
MIL-S-85420 - Sealing Compounds, Quick Repair, Low Temperature Curing Polysulfide, For Aircraft Structures
This specification establishes requirements for two types and classes of a two component, low temperature curing, polysulfide, sealing compound for use as a quick-repair material for aircraft structure.
MIL-S-8784 - Sealing Compound, Low Adhesion, For Removable Panels And Fuel Tank Inspection Plates
This specification covers two classes of accelerated synthetic rubber compounds for sealing access doors and accessories of integral fuel tanks, fuel cell cavities and accessories where gaskets are required.
MIL-S-8802 - Sealing Compound, Temperature-Resistant, Integral Fuel Tanks And Fuel Cell Cavities, High-Adhesion (S/S By Sae-Ams-S-8802)
This specification covers temperature-resistant -65 Deg. F to +250 Deg. F (-54 Deg. C to +121 Deg. C), two component synthetic rubber compounds of the polysulfide type for sealing and repairing integral fuel tanks and fuel cell cavities.
MIL-STD-340 - Coating, Pack Cementation, Chrome Aluminide, Process For (S/S By Mil-Hdbk-506)
This military standard covers the procedure for the application and inspection of a chrome aluminide pack cementation coating on TD nickel alloys.
MIL-STD-341 - Coating, Aluminum And Silicon Diffusion, Process For (S/S By Mil-Hdbk-341)
MIL-T-11293 - Treatment, Mildew Resistant Copper Process (For Fabrics, Threads And Cordages).
MIL-T-13867 - Treatment, Moisture And Fungus Resistant For Fire Control Electrical And Electronic Instruments And Equipment
MIL-T-22361 - Thread Compound, Antiseize, Zinc Dust-Petrolatum (S/S By A-A-59313)
MIL-T-27730 - Tape, Antiseize, Tetrafluoroethylene, With Dispenser (S/S By A-A-58092)
This specification covers polytetrafluoroethylene tape, with dispenser, for use on liquid and gaseous oxygen systems.
MIL-T-4053 - Tape, Pressure-Sensitive, Adhesive (Corrosion-Resistant)
This specification covers one type of corrosion-resistant pressure-sensitive (glass cloth) tape for use in binding joints in low-pressure hot-air ducts where the temperature does not exceed 350 Degrees F.
MIL-T-45035 - Treatment, Mildew Resistant, Non-Copper Processes For Cotten Duck, Webbing And Sewed Items (S/S By Ccc-D-950)
MIL-T-47012 - Tape, Pressure-Sensitive Adhesive, Copper Foil
MIL-T-47014 - Tape, Aluminum Foil, Pressure-Sensitive, Heat Reflective (S/S By A-A-59258)
This specification covers the requirements for one type of heat reflective aluminum foil pressure-sensitive tape intended for use at elevated temperatures.
MIL-T-5542 - Thread Compound, Anti Seize Oxygen Systems (S/S By Mil-G-27617 Now Mil-Prf-27617)
MIL-T-5544 - Thread Compound, Antiseize, Graphite-Petrolatum (S/S By Sae-Ams2518)
MIL-T-81287 - Tape, Pressure-Sensitive Adhesive, Aluminum Foil Backed, For High Temperature Application
MIL-W-10427 - Water-Repellent Compound, Filter Material Finish
MIL-W-13518 - Wood Preservative: Tetrachlorophenol And Pentachlorophenol Surface Sealing Compound
This specification covers preservatives for treating wood and plywood.
MIL-W-18142 - Wood Preservative Solutions, Oil-Soluble, Ship And Boat Use
This specification establishes the requirements for oil soluble wood preservative solutions for the non-pressure treatment of ship and boat building lumber and plywood.
MIL-W-20298 - Waterproofing Compound
MIL-W-3172 - Wax, Laboratory (Chattertons Compound)
MIL-W-3354 - Water-Repellent Treatment (For Glass Fabric)
MIL-W-46101 - Wood Preservation, Water Repellent (For Wood To Be Painted)
MIL-W-71125 - Wood Preservatives: Waterborne Or Water Reducible (S/S By A-A-59276)
MS18069 - Compounds, Adhesive, Aircraft Design And Use Limitations For Threaded Components Retained, Sealed Or Locked By
MS35496 - Antiseize Compound
MS35498 - Calking Compound
MS35504 - Coating, Compound, Bituminous Emulsion
MS35505 - Coating, Compound, Bituminous Solvent
MS35506 - Coating, Exterior, Air-Drying, For 1 Ton Containers
MS35510 - Compound, Calking, Plastic
MS35516 - Corrosion Resistant Coating, Chemically Treated Aluminum.
MS35538 - Glazing Compound, Sash
MS35551 - Mildew Resistant Compound, Textile
MS35554 - Paint, Acid, Proof
MS35604 - Preservative Coating, Canvas
MS35615 - Putty
MS35620 - Sealing Compound
MS35621 - Sealing Compound
MS35639 - Wood Preservative, Copper Naphthenate
MS35640 - Wood Preservative, Pentachlorophenol Mixture
MS35641 - Wood Preservative, Pentachlorophenol Mixture
MS35694 - Coating Compound, Metal Pretreatment, Resin&Acid
MS35699 - Wood Preservative, Acid Copper Chromate, Colors, Container Sizes, And Use Characteristics Thereof (Use Tt-W-546)
MS35700 - Wood Preservative, Ammonical Copper Arsenite (Use Tt-W-549)
MS35701 - Wood Preservative, Chromated Zinc Chloride (Use Tt-W-551)
MS35702 - Wood Preservative, Wolman Salt
MS35708 - Coating Compound, Bituminous Solvent Type (Use Mil-C-13950)
MS35710 - Corrosion Preventive Compound, Hot Application (Use Mil-C-15167)
MS35729 - Wood Preservative, Pentachlorophenal Mixture (Use Mil-W-18142)
MS35742 - Coating Compound, Bituminous Solvent, Colors, Container Sizes, And Use Characterisics Thereof (Use Mil-P-1227)
O-B-160 - Belt Dressing, Leather
O-G-93 - Galvanizing Repair Compound
O-L-164 - Leather Dressing, Mildew Preventive
O-L-169 - Leather Dressing, Transmission-Belt (S/S By O-B-160)
O-L-172 - Leather Dressing, Vesicant Gas Resistant
QPL-0083933-21 - Corrosion Preventive Compound, Cold Application (For Motor Vehicles)
QPL-10036-12 - Rust Arresting Coating (For Treatment Of Rusted Metal)
QPL-102-2 - Coating Compound, Bituminous, Solvent Cutback, Box And Crate Topcoating
QPL-11030-3 - Sealing Compound, Non-Curing, Polysulfide Base
QPL-11031-4 - Sealing Compound Adhesive, Curing (Polysulfide)
QPL-11520-11 - Preservative Coating, Rubber, For Rubber Surfaces
QPL-11796-31 - Corrosion Preventive Compound, Petrolatum Hot Application (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-12158 - Sealing Compound, Non-Curing, Polybutene
QPL-14201-7 - Corrosion Preventive, Soft Film, Cold Application (Use Mil-C-16173)
QPL-14231-4 - Sealing Compound, Joint, Two & Component, For Bolted Aluminum Or Steel Petroleum-Storage Tanks
QPL-149-12 - Plastic Coating Compound, Strippable (Hot Dipping)
QPL-15074-41 - Corrosion Preventive, Fingerprint Remover (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-15076-3 - Protective&Coating&Material, (Polymer&Powder )Product Of An Organic Dihalide And An Inorganic Polysulfide()
QPL-15143-1 - Protective-Coating (Heat-Hardening), Phenol-Formaldehyde
QPL-15159-15 - Preservative Coating, Canvas (Use Tt-P-595)
QPL-15203-6 - Coating Compound, Bituminous, Emulsion Type
QPL-15204-16 - Sealing Compound, Joint And Thread, High Temperature
QPL-15205-44 - Metal Conditioning Compound
QPL-16173-84 - Corrosion Preventive Compound, Solvent Cutback, Cold-Application (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-16555-6 - Coating Compound, Strippable, Sprayable
QPL-16558-5 - Coating, Organic (For Covering Shafts, Struts, And Other Exposed Surfaces)
QPL-17377-4 - Sealing Compound, Boiler-Casing
QPL-18255-28 - Calking Compound, Synthetic Rubber Base, Wooden Deck Seam Application
QPL-18487-10 - Compound, Gun Slushing
QPL-18623-1 - Plastic Coating Compound, Electrical Cable Splice Sealing, Naval Shipboard
QPL-18969-17 - Calking Compound, Metal Seam And Wood Seam
QPL-19565-26 - Coating Compound, Thermal Insulation, Fire-And Water-Resistant, Vapor-Barrier (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-19653-15 - Sealing Compound (Wood Bedding) Fortified
QPL-21066-4 - Coating System, Polyvinyl Chloride-Plasticizer Dispersion (Plastisol)
QPL-21067-8 - Coating Compound, Synthetic Rubber, Exposed Steel Surfaces
QPL-21595-10 - Tape, Pressure Sensitive Adhesive, Paper, Masking, Non-Staining
QPL-23112-7 - Corrosion Preventive, Fire Resistant (See Notice 1 For Replacement Information)
QPL-23142-4 - Tape, Pressure-Sensitive Adhesive, For Dissimilar Metal Separation
QPL-23498 - Sealing Compound Bearing Preservation Synthetic Rubber Base
QPL-23586-14 - Sealing Compound, (With Accelerator), Silicone Rubber, Electrical (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-24176-33 - Cement, Epoxy, Metal Repair And Hull Smoothing (Metric) (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-24205-1 - Calkink Compound, Modified Epoxy Base, Wooden Deck Seam Application
QPL-24340-13 - Sealing Compound, Deck, Polyurethane (Polyether Base)
QPL-25506-4 - Resin, Silicone, Low-Pressure Laminating
QPL-27315-4 - Coating Systems, Elastomeric, Thermally Reflective And Rain Erosion Resistant (See Notice 1 For Replacement Information)
QPL-27725-6 - Coating, Corrosion Preventive, For Aircraft Integral Fuel Tanks (Users May Refer To Pri-Qpl-Ams-C-27725)
QPL-2912-10 - Synthetic Rubber Compound, Acid And Oil Resistant (For Lining Battery Compartments On Submarines)
QPL-3105-23 - Sealing Compound, Inert (For Use In Ammunition)
QPL-3254-4 - Coating&System, Bridging, Strippable Sprayable
QPL-3301-17 - Compound, Asphaltic, Hot-Melt (Cavity Lining)
QPL-3927-1 - Thread Sealing Composition, Room Temperature Polymerizing
QPL-40084-4 - Corrosion Preventive Compound, Water-Emulsifiable, Oil Type
QPL-4383-12 - Sealing Compound, Topcoat, Fuel Tank, Buna-N Type (S/S By Qpl-Ams-S-4383)
QPL-450-11 - Coating Compound, Bituminous Solvent Type, Black (For Ammunition)
QPL-45021 - Plastic Coating Compound, Strippable, Cold Dipping 120 Deg., F. (49 Deg. C)
QPL-5542-9 - Thread Compound, Anti Seize Oxygen System
QPL-62218-8 - Corrosion Preventive Compounds, Cold-Application (For New And Fielded Motor Vehicles And Trailers)
QPL-6799-18 - Coatings, Sprayable, Stripple, Protective Water Emulsion (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-6869-21 - Impregnants For Aluminum Alloy And Magnesium Alloy Castings
QPL-7124-9 - Sealing Compound, Polysulfide, Accelerator Required, For Aircraft Structures
QPL-7126-7 - Sealing Compound, Synthetic Glass
QPL-7439-6 - Coating System, Elastomeric, Rain Erosion Resistant And Rain Erosion Resistant With Anti-Static Treatment, For Exterior Aircraft And Missile Plastic Parts
QPL-7502-14 - Sealing Compound, Integral Fuel Tanks And Fuel Cell Cavities High Adhesion, Accelerator Required
QPL-7916-3 - Sealing Compound, Thread And Gasket, Fuel, Oil And Water Resistant
QPL-8045-5 - Plastic, Self-Sealing Tank Backing Material
QPL-8067-1 - Leather Dressing, Fungus-Preventative
QPL-81287-1 - Tape, Pressure-Sensitive Adhesive, Aluminum Foil Backed, For High Temperature Application
QPL-81309-22 - Corrosion Preventive Compounds, Water Displacing, Ultra-Thin Film (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-8141-7 - Strippable Plastic Coating, Sprayable
QPL-81733-10 - Sealing And Coating Compound, Corrosion Inhibitive (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-81945-7 - Coating Compounds, Weapon Insulation, Intumescent (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-82604-2 - Compound, Asphaltic, High Melting Hot-Melt (Cavity Lining)
QPL-82633-2 - Compound, Polymeric Elastomer, Thermosetting (For Use As Bomb Tail Pad)
QPL-83315-4 - Sealing Compound, Aluminum Structure, Pressure And Weather Sealing, Low Density
QPL-83318-6 - Sealing Compound, Low Temperature Curing, Quick Repair, Integral Fuel Tanks And Fuel Cell Cavities
QPL-83430-13 - Sealing Compound, Integral Fuel Tanks And Fuel Cell Cavities, Intermittent Use To 360 Deg. F (182 Deg. C) (S/S By Qpl-Ams-3276)
QPL-83455 - Potting Compound, Two Component, Rtv, Fluorosilicone
QPL-83982-1 - Compound, Sealing, Fluid Resistant
QPL-8516-25 - Sealing Compound, Synthetic Rubber, Electric Connectors And Electric Systems, Chemically Cured (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-85334-4 - Sealing Compound, Non-Curling, Low Consistency, Silicone, Groove Injection, For Integral Fuel Tanks (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-8784-6 - Sealing Compound, Aluminum Integral Fuel Tanks And Fuel Cell Cavities, Low Adhesion, Accelerator Required
QPL-8802-23 - Sealing Compound, Temperature-Resistant, Integral Fuel Tanks And Fuel Cell Cavities, High-Adhesion
QPL-9063-9 - Desealant, Integral Fuel And Oil Tanks
QPL-907-46 - Antiseize Thread Compound, High Temperature (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-9118-7 - Finish, For Glass Fabric
QPL-AMS3276-4 - Sealing Compound, Integral Fuel Tanks And General Purpose, Intermittent Use To 360 Deg. F (182 Deg. C) (Users May Refer To Pri-Qpl-Ams3276)
QPL-AMS3277-2 - Sealing Compound, Polythioether Integral Fuel Tanks And General Purpose, Fast Curing Intermittent Use To 360 Deg. F (182 Deg. C) (Users May Refer To Pri-Qpl-Ams3277)
QPL-AMS3281-4 - Sealing Compound, Polysulfide (T) Synthetic Rubber For Integral Fuel Tank And Fuel Cell Cavities Low Density (1.35 Sp Gr Max), For Intermittent Use To 360 Deg. F (182 Deg. C) (Users May Refer To Pri-Qpl-Ams3281)
QPL-TT-C-520-9 - Coating Compound, Bituminous, Solvent Type, Underbody (For Motor Vehicles)
QPL-TT-C-530-3 - Coating Compound, Rust Inhibitive, Fish Oil Base
QPL-TT-P-595-3 - Preservative Coating, Canvas
QQ-C-100 - Cement, Iron And Steel
R-T-111 - Tar, For Joint Filler
SS-C-560 - Coating-Material, Fatty Acid Pitch Base, (Nonbleeding) Brushing And Spraying Consistency (For Foundations, Roofs, Walls, Etc.)
SS-C-608 - Compounds, Jointing, Sulfur (For Bell-And-Spigot Cast-Iron Pipe)
SS-P-680 - Priming-Material, Fatty Acid Pitch Base, Brushing And Spraying Consistency (For Concrete, Masonry, And Other Mineral Surfaces)
SS-S-001416 - Sealing Compound, Asphalt And Concrete Surfaces
SS-S-1401 - Sealant, Joint, Non-Jet-Fuel-Resistant, Hot-Applied, For Portland Cement And Asphalt Concrete Pavements (No S/S Documents)
This specification covers one type of one-component, hot-applied material for use in sealing joints and cracks in portland cement and asphalt concrete pavements.
SS-S-156 - Sealer, Cold Application, Emulsion Type, For Joints In Concrete (Use Ss-S-200)
SS-S-158 - Sealing Compound, Cold-Application Ready-Mixed Liquefier Type, For Joints In Concrete (Use Ss-S-156)
SS-S-159 - Sealing Compound, Cold-Application Mastic Multiple Component Type-For Joints In Concrete
SS-S-1614 - Sealants, Joint, Jet-Fuel-Resistant, Hot-Applied, For Portland Cement And Tar Concrete Pavements
This specification covers two types and two classes of one-component, jet-fuel-resistant, hot-applied material for use in sealing joints and cracks in portland cement and tar concrete pavements.
SS-S-164 - Sealer, Hot Poured Type, For Joints In Concrete (Use S5-S-1401)
SS-S-167 - Sealing Compound, Jet-Fuel Resistant, Hot Applied, Concrete Paving (Use Ss-S-1614)
SS-S-168 - Sealing Compound, Sewer, Bituminous Two Component, Mineral Filled, Cold Applied (See Ss-S-169)
SS-S-169 - Sealer, Joint, Sewer, Mineral-Filled, Hot-Pour
SS-S-170 - Sealing Compound, Two Components, Jet Fuel Resistant, Cold Applied, Concrete Paving (Use Ss-S-200)
SS-S-171 - Sealer, Mineral-Filled Asphalt, For Joints In Concrete (Use Ss-S-1041)
SS-S-195 - Sealing Compound, Two Component, Elastomeric, Polmer Type, Cold Applied, Concrete Paving Joints (Use Ss-S-200)
SS-S-1996 - Sealer, Water And Weather Resistant, For Asphalt, Concrete, And Masonry Surfaces
SS-S-200 - ( Images) Sealant, Joint, Two Component, Jet Blast Resistant, Cold Applied,For Portland Cement Concrete Pavement
This specification covers two types of two-component, elastomeric, cold-applied, jet-fuel-and jet-blast-resistant sealing compounds for use in sealing joints and cracks in portland cement concrete pavement.
SS-S-210 - Sealing Compound, Preformed Plastic, For Expansion Joints And Pipe Joints
This specification covers a cold-applied preformed plastic sealing compound for sealing expansion joints and tongue and groove joints of concrete pipe culvert, storm drain and sewer pipe.
SS-W-110 - Water Repellent, Colorless, Silicone Resin Base
TT-A-580 - Antiseize Compound, White Lead Base General Purpose (For Threaded Fittings) Use Tt-S-1732
TT-C-00493 - Coating Compound, Bituminous, Solvent Type, Asphalt Base And Aluminum Pigmented For Roofs (S/S By Tt-C-04498)
TT-C-1079 - Coating Compound Bitumindus, Solvent Type, Asbestos Filled, Aluminum Pigmented (Use Tt-C-498)
TT-C-1796 - ( Images) Calking Compounds, Metal Seam And Wood Seam (S/S By A-A-272)
This specification covers calking compound for use as a calking material on metal and wood structures, and as a sealant for applications requiring the use of putty.
TT-C-494 - Coating Compound, Bituminous, Solvent Type Acid-Resistant
TT-C-495 - Coating, Exterior, For Tinned Food Cans
This specification covers coatings applied to the outside of tinned food cans.
TT-C-498 - Coating Compound, Bituminous, Fillers, Solvent Type, Aluminum Pigmented
TT-C-517 - Coating, Strippable Masking, (For Spray Booths And Glass)
TT-C-520 - ( Images) Coating Compound, Bituminous, Solvent Type, Underbody (For Motor Vehicles)(S/S By Mil-C-62218)
This specification covers an asphalt compound suitable for use as a protective coating and sound deadener on the underbody parts of automotive equipment.
TT-C-598 - ( Images) Calking Compound, Oil And Resin Base Type (For Masonary And Other Structures) (S/S By A-A-272)
This specification covers the properties of a one-component oil and/or resin base calking compound for use in masonary and other types of structures.
TT-F-1098 - Filler, Block Solvent Thinner, For Porous Surfaces (Concrete Block, Cinder Block, Stucco, Etc.)
TT-F-336 - Filler, Wood, Paste
TT-F-340 - Filler, Wood, Plastic
This specification covers a plastic wood filler suitable for use with acetone solvent and for such repair work as building up or filling in wood patterns or joiner work.
TT-G-410 - Clazing Compound, Sash (Metal) For Back Bedding And Face Glazing (Not For Channel Or Stop Glazing) (S/S By Astm-C669)
TT-P-00791 - Putty, Linseed-Oil Type, (For Wood-Sash-Glazing) (S/S By A-A-378)
TT-P-1536 - Plumbing Fixture Setting Compound (S/S By A-A-3110)
TT-P-595 - Preservative Coating, Canvas
TT-P-781 - Putty And Elastic-Compound, (For) Metal-Sash-Glazing (S/S By Tt-G-410)
TT-P-791 - Putty, Pure-Linseed-Oil, For Wood-Sash Glazing (S/S By A-A-378)
TT-S-001657 - ( Images) Sealing Compound Single Component, Butyl Rubber Based, Solvent Release Type (For Buildings And Other Types Of Construction) (S/S By A-A-272)
This specification covers the properties of a single component, solvent release type, butyl rubber based sealing compound for sealing, calking, and glazing operations in buildings and other types of construction.
TT-S-00227 - ( Images) Sealing Compound, Elastomeric Type, Multi-Component (For Calking, Sealing, And Glazing In Buildings And Other Structures) (S/S By A-A-1556)
This specification covers the properties of a multi-component cold-applied elastomeric type joint sealing compound (joint sealant), including curing agents, for sealing, calking, and glazing operations in buildings, building areas (plates, decks, pavements, etc.) and other types of construction.
TT-S-1732 - Sealing Compound, Pipe Joint And Thread, Lead Free General Purpose
This specification covers a lead free, antiseize sealing compound for use in joints and threaded parts on low-pressure steam and water lines.
TT-S-222 - Sealing Compound: Asbestos
TT-S-227 - ( Images) Sealing Compound, Rubber Base, Two Component (For Caulking, Sealing, And Glazing In Building Construction (S/S By A-A-1556)
This specification covers the properties of a two-component cold-applied synthetic rubber base joint sealing compound, including curing agents, for sealing, calking, or glazing application in buildings and other types of construction.
TT-S-230 - ( Images) Sealing Compound: Elastomeric Type, Single Component (For Calking, Sealing, And Glazing In Building And Other Structures)
This specification covers the properties of a single component, cold-applied elastomeric type joint sealing compound (joint Sealant) for sealing, calking, and glazing operations in buildings, building areas (plazas, decks, pavements, etc.), and other types of construction.
TT-W-156 - Water-Repellent Compound, Textile Finish
TT-W-535 - Wood Preservative: Fluor Chrome Arsenate Phenol Mixture (S/S By Awpa Std P5 Standards For Waterborne Preservatives, No. 8)
This specification covers the composition and methods of analysis of a fluor chrome arsenate phenol treating solution for the preservative treatment of wood according to TT-W-571 (see 6.1), and also a strong solution suitable for the brush treatment of the cut ends of treated wood products.
TT-W-538 - Wood Preservative, Chromated Zinc Arsenate Mixture
TT-W-546 - Wood Preservative: Acid Copper Chromate Mixture (S/S By Awpa-P5)
This specification covers the composition and methods of analysis of acid copper chromate treating solutions for the preservative treatment of wood according to Federal Specification TT-W-571 (see 6.1), and also strong solutions suitable for the brush treatment of the cut ends of treated wood products.
TT-W-549 - Wood Preservative: Ammoniacal Copper Arsenate Mixture (S/S By Awpa-P5)
This specification covers the composition and methods of analysis of an ammoniacal copper arsenate treating solution for the preservative treatment of wood according to Federal Specification TT-W-571 (6.1), and also a strong solution suitable for the brush treatment of the cut ends of treated wood products.
TT-W-550 - Wood, Preservative: Chromated Copper Arsenate Mixture
This specification covers the composition and methods of analysis of chromated copper arsenate, of a waterborne solution used for the preservative treatment of wood in accordance with TT-W-571 (see 6.1), and also of a strong solution suitable for the brush treatment of the cut ends of treated wood products.
TT-W-551 - Wood Preservative, Chromated Zinc Chloride Mixture
This specification covers the composition and methods of analysis of chromated zinc chloride treating solutions for the preservative treatment of wood according to Federal Specification TT-W-571 (see 6.1), and also strong solutions suitable for the brush treatment of the cut ends of treated wood products.
TT-W-562 - Wood Preservative, Copperized Chromated Zinc Chloride Mixture
TT-W-566 - Wood-Preservative, Creosote-Coal-Tar Solution
TT-W-568 - Wood Preservative; Creosote-Petroleum Solution
TT-W-569 - Wood Preservative, Osmosar (Osmosalts)
TT-W-570 - Wood Preservative, Pentachorophenol, Solid (Use Astm-D1272)
VV-S-190 - Sealing Compound, Dipcoating
This specification covers one grade of sealing compound suitable for the sealing of wrappings or packages by dipcoating.
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business